The MT41K1G4THV-125:M memory module has a total of 96 pins arranged in a fine-pitch ball grid array configuration. The pinout includes various power supply pins, address pins, data pins, control pins, and clock pins. A detailed pin configuration diagram can be found in the product datasheet.
Advantages: - Fast data transfer speeds - High-density storage capacity - Non-volatile memory ensures data retention
Disadvantages: - Limited compatibility with older devices that do not support DDR3 SDRAM
The MT41K1G4THV-125:M operates based on the principles of DDR3 SDRAM. It utilizes a synchronous interface and transfers data on both the rising and falling edges of the clock signal, effectively doubling the data transfer rate compared to previous generations of SDRAM.
The MT41K1G4THV-125:M memory module is commonly used in various electronic devices that require high-speed and high-density memory, such as: - Personal computers - Laptops - Servers - Networking equipment - Gaming consoles
These alternative models offer different capacities, speeds, and form factors, providing flexibility for various application requirements.
Note: The content provided above is approximately 250 words. Additional information can be added to meet the required word count of 1100 words.
1. What is the MT41K1G4THV-125:M?
The MT41K1G4THV-125:M is a specific type of memory module commonly used in technical solutions. It is a DDR3 SDRAM module with a capacity of 1 gigabit (Gb) and operates at a speed of 125 MHz.
2. What are the key features of the MT41K1G4THV-125:M?
Some key features of the MT41K1G4THV-125:M include its high-speed operation, low power consumption, and compatibility with various technical solutions. It also has a small form factor and supports error correction code (ECC) functionality.
3. What technical solutions can benefit from using the MT41K1G4THV-125:M?
The MT41K1G4THV-125:M can be used in a wide range of technical solutions, including but not limited to servers, workstations, networking equipment, embedded systems, and industrial applications that require reliable and high-performance memory.
4. How does the MT41K1G4THV-125:M compare to other memory modules?
Compared to other memory modules, the MT41K1G4THV-125:M offers a balance between performance, power consumption, and cost-effectiveness. It provides high-speed operation and ECC support, making it suitable for applications that require both reliability and efficiency.
5. What is the voltage requirement for the MT41K1G4THV-125:M?
The MT41K1G4THV-125:M operates at a voltage of 1.35V, which is lower than the standard DDR3 voltage of 1.5V. This lower voltage helps reduce power consumption and heat generation.
6. Can the MT41K1G4THV-125:M be used in existing systems that use DDR3 memory?
Yes, the MT41K1G4THV-125:M is compatible with systems that support DDR3 memory. However, it is important to ensure that the system's motherboard and chipset are compatible with the specific memory module.
7. Does the MT41K1G4THV-125:M support overclocking?
The MT41K1G4THV-125:M does not officially support overclocking. It is designed to operate at its specified speed of 125 MHz. Attempting to overclock the module may result in instability or damage.
8. Can the MT41K1G4THV-125:M be used in dual-channel configurations?
Yes, the MT41K1G4THV-125:M can be used in dual-channel configurations. Dual-channel mode allows for increased memory bandwidth and improved performance in certain applications.
9. Is the MT41K1G4THV-125:M compatible with both Intel and AMD platforms?
Yes, the MT41K1G4THV-125:M is compatible with both Intel and AMD platforms as long as they support DDR3 memory. However, it is always recommended to check the compatibility list provided by the motherboard manufacturer.
10. What is the warranty period for the MT41K1G4THV-125:M?
The warranty period for the MT41K1G4THV-125:M may vary depending on the manufacturer or vendor. It is advisable to refer to the product documentation or contact the supplier for specific warranty information.