Texas Instruments
Kuva saattaa olla esitys.
Katso tuotteen tekniset tiedot.
SN74ALS645AN
Näytä Yksityiskohdat DataSheets

SN74ALS645AN

Product Overview

  • Category: Integrated Circuit
  • Use: Bus Transceiver
  • Characteristics:
    • High-speed, low-power device
    • Compatible with TTL and CMOS logic levels
    • Bidirectional data flow
    • Non-inverting outputs
  • Package: DIP (Dual In-line Package)
  • Essence: Transfers data between two bidirectional buses or systems
  • Packaging/Quantity: Available in tubes of 25 units

Specifications

  • Supply Voltage: 4.5V to 5.5V
  • Input Voltage: 0V to VCC
  • Output Voltage: 0V to VCC
  • Operating Temperature Range: -40°C to +85°C
  • Maximum Propagation Delay: 10ns
  • Maximum Operating Frequency: 100MHz

Detailed Pin Configuration

The SN74ALS645AN has a total of 20 pins, which are assigned as follows:

  1. DIR (Direction Control)
  2. OE (Output Enable)
  3. A1 (Bus A Data Input/Output)
  4. A2 (Bus A Data Input/Output)
  5. A3 (Bus A Data Input/Output)
  6. A4 (Bus A Data Input/Output)
  7. A5 (Bus A Data Input/Output)
  8. GND (Ground)
  9. B5 (Bus B Data Input/Output)
  10. B4 (Bus B Data Input/Output)
  11. B3 (Bus B Data Input/Output)
  12. B2 (Bus B Data Input/Output)
  13. B1 (Bus B Data Input/Output)
  14. VCC (Supply Voltage)
  15. B6 (Bus B Data Input/Output)
  16. B7 (Bus B Data Input/Output)
  17. B8 (Bus B Data Input/Output)
  18. B9 (Bus B Data Input/Output)
  19. B10 (Bus B Data Input/Output)
  20. GND (Ground)

Functional Features

  • Bidirectional data transfer between two buses
  • Non-inverting outputs ensure data integrity
  • High-speed operation allows for efficient data transmission
  • TTL and CMOS compatibility enables easy integration into existing systems
  • Direction control pin allows for flexible data flow management
  • Output enable pin provides additional control over the transceiver

Advantages and Disadvantages

Advantages: - High-speed operation - Compatible with TTL and CMOS logic levels - Bidirectional data flow - Non-inverting outputs

Disadvantages: - Limited operating temperature range (-40°C to +85°C) - Maximum propagation delay of 10ns may not be suitable for certain applications

Working Principles

The SN74ALS645AN is a bus transceiver that facilitates bidirectional data transfer between two buses or systems. It operates by receiving data from one bus and transmitting it to the other, while also allowing data to flow in the opposite direction. The direction control pin determines the data flow direction, while the output enable pin enables or disables the outputs. The device is designed to operate at high speeds and is compatible with both TTL and CMOS logic levels.

Detailed Application Field Plans

The SN74ALS645AN can be used in various applications where bidirectional data transfer between two buses is required. Some potential application fields include:

  1. Computer Systems: Facilitating communication between different subsystems within a computer.
  2. Networking Equipment: Enabling data exchange between network interfaces.
  3. Industrial Automation: Connecting various control modules and sensors in automated systems.
  4. Telecommunications: Transferring data between different telecommunication equipment.
  5. Automotive Electronics: Integrating different electronic modules within a vehicle.

Detailed and Complete Alternative Models

  1. SN74ALS646AN: Similar to SN74ALS645AN, but with additional bus-hold circuitry for improved noise immunity.
  2. SN74ALS648AN: 8-bit version of the transceiver, providing higher data capacity.
  3. SN74ALS641AN: Octal bus transceiver with inverted outputs.

These alternative models offer similar functionality to the SN74ALS645AN and can be considered as alternatives based on specific requirements.

Word count: 445 words

Luettele 10 yleistä kysymystä ja vastausta, jotka liittyvät SN74ALS645AN :n soveltamiseen teknisissä ratkaisuissa

Sure! Here are 10 common questions and answers related to the application of SN74ALS645AN in technical solutions:

  1. Q: What is SN74ALS645AN? A: SN74ALS645AN is a type of integrated circuit (IC) commonly used as a bus transceiver or level shifter in digital systems.

  2. Q: What is the purpose of SN74ALS645AN? A: The purpose of SN74ALS645AN is to enable bidirectional data transfer between two buses with different voltage levels or signal formats.

  3. Q: What voltage levels does SN74ALS645AN support? A: SN74ALS645AN supports TTL (Transistor-Transistor Logic) voltage levels, typically 5V.

  4. Q: How many channels does SN74ALS645AN have? A: SN74ALS645AN has 8 bidirectional channels, allowing for simultaneous data transfer in both directions.

  5. Q: Can SN74ALS645AN be used with different logic families? A: Yes, SN74ALS645AN is compatible with various logic families such as TTL, CMOS, and LVTTL.

  6. Q: What is the maximum data rate supported by SN74ALS645AN? A: SN74ALS645AN can handle data rates up to 24 MHz, making it suitable for many standard digital communication protocols.

  7. Q: Does SN74ALS645AN require external components for operation? A: Yes, SN74ALS645AN requires external pull-up resistors and decoupling capacitors for proper functionality.

  8. Q: Can SN74ALS645AN be used in high-noise environments? A: Yes, SN74ALS645AN has built-in noise immunity features that make it suitable for use in high-noise environments.

  9. Q: Can SN74ALS645AN be used for level shifting between different voltage domains? A: Yes, SN74ALS645AN can be used to shift signals between different voltage domains, provided the voltage levels are within its specified range.

  10. Q: Are there any specific precautions to consider when using SN74ALS645AN? A: It is important to ensure proper power supply decoupling and avoid exceeding the maximum voltage and current ratings specified in the datasheet.

Please note that these answers are general and may vary depending on the specific application and requirements. Always refer to the datasheet and consult with an expert for accurate information.