XC6108N49AGR-G belongs to the category of integrated circuits (ICs).
It is commonly used as a voltage detector in electronic devices.
XC6108N49AGR-G is packaged in a SOT-23-5 package. It is available in quantities of [insert quantity].
The XC6108N49AGR-G has the following pin configuration:
```
| | --| VDD|-- Pin 1: Power supply --| GND|-- Pin 2: Ground --| VIN|-- Pin 3: Voltage input --| VOUT|-– Pin 4: Voltage output --| EN |-- Pin 5: Enable control |____| ```
XC6108N49AGR-G operates by comparing the input voltage (VIN) with a reference voltage. When the input voltage falls below the threshold, the output (VOUT) becomes active low, indicating a power failure or low battery condition.
XC6108N49AGR-G finds applications in various fields, including: 1. Battery-powered devices: Provides low battery detection and power management. 2. Consumer electronics: Monitors voltage levels to prevent damage to sensitive components. 3. Industrial equipment: Ensures stable operation by detecting power supply abnormalities. 4. Automotive systems: Protects electronic components from voltage fluctuations.
Other alternative models that offer similar functionality to XC6108N49AGR-G include: 1. [Model 1]: [Brief description] 2. [Model 2]: [Brief description] 3. [Model 3]: [Brief description]
Please note that the above information is subject to change. For the most accurate and up-to-date specifications, refer to the manufacturer's datasheet.
[Word count: 315]
Sure! Here are 10 common questions and answers related to the application of XC6108N49AGR-G in technical solutions:
Q: What is XC6108N49AGR-G? A: XC6108N49AGR-G is a voltage detector IC (integrated circuit) used for monitoring power supply voltages in various electronic devices.
Q: What is the operating voltage range of XC6108N49AGR-G? A: The operating voltage range of XC6108N49AGR-G is typically between 0.7V and 10V.
Q: What is the output configuration of XC6108N49AGR-G? A: XC6108N49AGR-G has an open-drain output configuration, which requires an external pull-up resistor.
Q: What is the purpose of using XC6108N49AGR-G in a technical solution? A: XC6108N49AGR-G is commonly used to monitor power supply voltages and provide a reset signal when the voltage falls below a certain threshold.
Q: What is the typical voltage threshold for triggering a reset signal with XC6108N49AGR-G? A: The typical voltage threshold for triggering a reset signal with XC6108N49AGR-G is 4.9V.
Q: Can XC6108N49AGR-G be used in battery-powered applications? A: Yes, XC6108N49AGR-G can be used in battery-powered applications as it has a low quiescent current consumption of typically 1.0µA.
Q: Is XC6108N49AGR-G suitable for automotive applications? A: Yes, XC6108N49AGR-G is suitable for automotive applications as it meets the AEC-Q100 Grade 2 automotive reliability standards.
Q: Does XC6108N49AGR-G have any built-in protection features? A: Yes, XC6108N49AGR-G has built-in overcurrent protection and thermal shutdown features to ensure safe operation.
Q: What is the package type of XC6108N49AGR-G? A: XC6108N49AGR-G is available in a small SOT-25 package, which is compact and suitable for space-constrained designs.
Q: Can XC6108N49AGR-G be used in industrial control systems? A: Yes, XC6108N49AGR-G can be used in industrial control systems as it operates reliably in a wide temperature range of -40°C to +105°C.
Please note that the answers provided here are general and may vary depending on the specific datasheet and application requirements.